ROBEX DK, s.r.o. - cutting technique, accessories, custom made machinery

SHOPWITH NOT ONLY
PROFESSIONALLY
TECHNIQUE CUSTOM
MADE SINGLE-PURPOSE
MACHINES

CART (0)

On-line catalogue - english

Other machinery, custom made special machines

Roll Slitting Machine - tapes from roles cutting

Paspulator PKV-2000 - roll cutter (foil, foam, rubber, textile)

The roll splitter is intended for transverse cutting of hard and soft materials when the roll of material is spun using a pressed rolled disc knife. Adjustable shaft speed limitation with material, central nut with mandrels to lock sleeve on shaft, quick face lock, two-handed safety trigger. The roll is cut including the paper tube (can be limited by a screw).

Detail: Cutting takes place using a disc knife with a large diameter, which is guided by a manually guided movable arm against the material rolled on a motor-driven shaft.The frame construction of the machine is made of steel + aluminum AluTec profiles. A linear guide with an arm guide is located on this frame in a horizontal plane. A disc knife is fixed on this arm. The shaft drive is an asynchronous motor with the possibility of a continuous speed change. Thanks to the used frequency converter, operation is also economical. The knife cover is opened by a wheel that runs along the upper part of the roll, i.e. the position of the arm above the material. The arm has a handle with a two-handed trigger, a manual lock for a strong hold of the arm at the point of the cut.The safety of the machine is ensured by the position, the cover and the safety double-circuit module.

on demand

Paspulator PKV-1000 - automatic film roll cutter

The foil roll divider is intended for transverse cutting of solid materials (when roll rotate) into paspules (discs) of different widths. A large cutting disc is used for cutting, which is guided into the cut by a motor (servo actuator) with a smooth change of speed. Adjustable speed limitation of the knife and rolling rollers, locking and a lesion indicator of the cutting position, controlled by the Siemens system. The automatic extraction of the chips is a matter of course.

Detail: Cutting takes place using a large-diameter disc knife, which is guided by a motor-guided arm against a material rolled on a pair of adjustable driven rollers. | | The construction of the machine frame consists of AluTec steel + aluminum profiles. A linear guide with an arm guide is located on this frame in the horizontal plane. A disc knife is mounted on this arm. The knife drive is an asynchronous motor located on this arm with the possibility of a smooth change of speed. The knife cover is opened by repacking, ie the position of the arm above the material. The arm has a handle for manual (quick) position change, a rolling wheel for precise, precise position adjustment, pneumatic locking for strong holding of the arm at the cutting site (without locking the cutting cycle cannot be started) and a laser pointer to facilitate measuring the cutting position. The arm is pushed into the cut by means of a servo drive. Driving upwards always takes place at maximum speed. The downward (cut) out of the material also takes place in accelerated mode. thanks to the inductive sensor, the movement of the arm is slowed down only before the height of the placed diameter of the roll is reached. Bosch Rexroth units are used to drive the arm. Ideal accuracy is also achieved by rolling the roll on rubberized rolling rollers, which are adjustable (for different roll diameters). A pair of Siemens frequency converters is used to drive the cylinders. A Siemens system with remote management is used for control. The whole system is built as a semi-automatic. Measuring the position of the cut manually, own cut fully automatic. Sawdust and chips are always removed from the cutting point into the plastic bag during the cut. Thanks to the branch, this extraction can also be used for manual vacuuming.

on demand

Paper tube divider RBRD-2 (diameter up to 500mm, wall thickness up to 35mm)

Machine for cutting and dividing paper and cardboard tubes up to a diameter of 500 mm with a wall thickness of 35 mm. The cut takes place by rolling the cutting disc along a rotating tube. The cut is made manually by pressing the blade on the cut tube through the lever of the cutting arm. The sockets are threaded on the central mandrel with a clamping disk.

Detail: The design of the machine is chosen simply and efficiently to achieve easy and safe operation by the operator. The basic supporting part with the drive and the cutting arm consists of a frame of welded construction made of steel profiles, the supporting frame of the separate tube is made of aluminum anodized profiles. Both parts are connected by screwed mounting plates. The superstructures are generally also made of aluminum anodised profiles. The surface treatment of steel parts is solved with powder firing paint and galvanic galvanizing The smooth rotation of the cut tube against the cutting disc is ensured by rolling on rubberized drive rollers, which also serve as a support when the blade is pressed against the tube. The required torque is determined by an electric motor with a gearbox and an output shaft fitted with a toothed pulley, which drives the pulleys by means of a toothed belt. The optimal tube speed is set by the manufacturer on the frequency converter and we do not recommend changing it.

on demand

Paspulator PS 5PP - fast rewinder with longitudinal division of rolls (when rewinding)

The automatic device is designed for longitudinal cutting of materials during rewinding from a roll of max ø 1150 mm, width 1,600 mm and weight 300 kg into strips (discs) of various widths, intended for further processing. Industrial razor blades are used for cutting, with the possibility of their mutual distribution across the entire width. Adjustable speed limit, side straightening, controlled by PLC with touch. screen and measuring length, rewinding speed up to 2.7 m / s.

Tech. specification: Electrical supply: 3NPE 400V / 50Hz TN-S | Power input: 8.1kW | | Rewind / cutting speed: automatically variable (min. 2.0m/s, max. 2.7m/s) | Motor: 2x SM controlled as servo | Cut: razor blades on interchangeable holder | Control: PLC + HMI with touch screen | The device can be used as a viewing and rewinding machine with straightening edges Input Roles: | Material: 17-110g/m2 | Roll diameter max.: 1150mm | Roll weight max.: 300Kg | Roll width max.: 1600mm | Inner diameter of roll sleeve: 76 mm | Output Roles: | Output roll: according to the set required length (cm) | Roll weight max.: 300kg | Rewinding working speed (minimum): 120 m/min (at 100% potentiometer) | Razor safety covers for changing brackets

Detail: To achieve the required dimensional tolerance, the most suitable method of cutting during rewinding is. Cutting takes place using razor blades on a rising frame while rewinding the roll of material. | | The construction of the machine frame consists of steel + aluminum profiles AluTec. The unwinding and winding shaft is expansion, pneumatic for the inner ø of the tube 76 mm. The ends of the winding shaft are square in shape. The shaft is mounted in tilting bearing housings, driven by an electric motor with a gearbox, where servo control with a speed of 0-3000 rpm is used. Before clamping and before introducing the material, it is necessary to arrange the divided cavities on the shaft according to the required dimensions. | | The speed is controlled by connecting the roll diameter sensors / potentiometer / dancer so that it is always min. 2m / s. The PLC with a touch screen also displays the currently measured length. | | The razor holders are slidably mounted on a removable aluminum profile, mounted on a tilting arm. Removable aluminum profiles (2 pcs.) For easy and quick exchange of cut positions. Latches with a tension spring located on a fixed central frame are used to secure this arm in the rest position. | | The device aligns the edges of the laid material. Based on a pair of sensors, the system allows the transverse movement of the material so that its edge is always guided on the winding shaft in the same place. The position of the sensor in the transverse direction can be adjusted to a certain extent and thus determine the position of the edge of the material.

on demand

NC controlled full automatic machine RBP - NC for precision transverse cutting

Paspulator RBP - NC is designed for transverse paspule cutting. Cutting from rolls of woven and non-woven fabrics or coated textile and similar materials, for further processing. RBP - NC operates in full automatic mode. The actuators are designed using stepper motors with high precision positioning of settings and programs.

Detail: High precision cutting machine with PLC controller. You can save and load all set parametrs to (from) memory. |

on demand

Papulator RB PP-2 - roll cutting while rewinding

The machine is designed for cutting materials when rewinding from a roll of max. 450 mm, width 1 500 mm and weight 280 kg to belts (rolls) of different widths. Equipped with a frequency converter for continuous speed change, pneumatic brake, side straight, controlled by PLC with touch. these and length measuring.

Detail: To achieve the required dimensional tolerance, the best way to cut is during rewinding. Cutting is carried out using razor blades on a rising frame while rewinding the roll of material. | | The frame of the machine is made of steel + aluminum profiles AluTec. The unwinding and winding shaft is expandable, pneumatic for the inner diameter of the tube 76 mm. The ends of the winding shaft are square-shaped. The shaft is placed in hinged bearing houses, driven by an electric motor with gearbox. Prior to clamping and material insertion, it is necessary to arrange the split tubes according to the required dimensions on the shaft. | | The touch screen PLC also displays the currently measured length. | | The tension of the material required during rewinding and cutting is ensured by wrapping it through the braked cylinder. It is braked by a pneumatic friction brake, the effect of which is regulated by a pneumatic pressure reducer. The blade holders are slidingly mounted on a removable aluminum profile attached to the swing arm. Removable aluminum profiles (2pcs) for easy and quick change of cut positions. To secure this arm in the rest position, use the tension spring latches located on the fixed central frame. To prevent unwinding of the roll of material in the unwinding part, the machine will be equipped with a belt friction brake with a weight. A friction disc is mounted on the shaft at the friction brake strap. | | The machine aligns the edges of the material to be laid. The system allows the transverse movement of the material, based on the sensor, so that its edge is always guided to the winding shaft at the same location. The transverse sensor position can be adjusted to a certain extent to determine the position of the material edge. The range of movement for holding the edge is + 70 mm.

on demand

Paspulator - machine for roles cutting RBP 1500

Special machine for cutting material in roles. Cutting mechanism for perfect accuracy. It is good for cut tape or pile sides of role. Paspulator has statical special knife, pneumatical shaft for fast change of role, frequency modulation for speed change, double-hand starting of machine and other funnctons.

Detail: Can you cut tape from role? Can you pile sides of role?Paspulator is machine fit for cutting from role without rewinding material. It is our machine with genial use. You insert your role to pneumatical shaft, measure position of cut and start machine. Special knife is good for material cutting with paper cup or without paper cut. General summary: | gripping of the role with material on stretching pneumatic shaft (length to 6.2m) | support rollers for inhibits shaft deflection | gripping of the shaft into the special fastener bearings | automatic variation in revolutions dependent on process of cut (possibility) | cutting mechanism special wrought knife, bayonet gripping of the knife for angular setting | (according to different materials various types of the knives) | axially linear shift of the cutting mechanism with pneumatic brake in linear Alu lead | machine suits to all norms of Czech republic and EU |

on demand

Paspulator - cutting role, chaff - self-generating method PRR-O/MIL

Machine on dividing material in role inclusive possibilities kerf margin role. Cheapen variant machinery on dividing textile material self-generating method!

Detail: instrumental towards coarse, but very nice trim role, cut material. Quality cut directly unwind from qualities winding-up input material.

on demand

Paspulator - machine for cutting role with rewind PP–1/HR

Machine for cutting role with rewind. Super quality cutting.

Detail: Lengthwise cutting unwoven textile wound at role. Cutting proceed by the help of special industrial blade placed on rampant frame, at contemporary rewinding role material.

on demand

Paspulator - machine for cutting role with rewind PP–2

Machine for cutting role with rewind. Super quality cutting.

Detail: Lengthwise cutting unwoven textile wound at role. Cutting proceed by the help of circural blades placed on rampant frame, at contemporary rewinding role material.

on demand

Next special custom made machinery

Automatic tape divider DPR-4

The divider is intended for dividing tape according to pre-defined and user-changeable (USB import/export) recipes. An oval section and a pair of holes for the belt clip are created in the belt, and then a defined number of holes with a set spacing are placed in position. The end of the tape is finished with a straight cut or a cut to a point. The Kinco control system with a 7-inch touch screen allows remote management connection.

Detail: The machine consists of the following parts:An unwinder controlled independently by a dancer with a pair of induction sensors, while the lower sensor creates a supply loop for the voltage-free thrust of the position motors, the upper sensor accelerates the unwinding. | | Input part with tape positioning within a tolerance of 0.3 mm (1600 imp. / 1 turn), accuracy can be increased up to 10x. This rolling section positions the belt under the individual tools, while the positions are calculated using the PLC, according to the currently selected recipe. The position of the oval is defined by the center, while its distance from the actual beginning of the tape is defined in the recipe. The center of the oval is the bend of the tape, where the buckle is inserted and the tongue of the buckle passes through this place.The punch is designed as a punch guided on a pneumatic cylinder with a short stroke and high force. The waste from the holes falls into the drawer box at the bottom of the track. The holes are used not only on the buckle, but also as the middle part of the tape, where the distance of the first hole on the tape, the number of directs and their spacing are defined.The straight section defines the position of the tape with the first section 0 (origin). It is guided on a pneumatic cylinder against the pad / block. A straight cut always occurs, even if the recipe is set to an arrow cut. The straight cut occurs at the position of the total length of the tape.The cut to the tip is an optional part of the recipe. This is the most common tape termination when using a buckle. As with other tools, a pneumatic cylinder is used for guidance. The waste from the tip section is taken out into the drawer box.The ejector is controlled positionally just like the positional part | Kinco control system with a 7-inch touch screen for recalling recipes, setting length, delay, speed incl. options for displaying the service and diagnostic menu. The display also shows error messages, the time to complete the operation, according to the set number of pieces, etc.The system can be equipped with remote management for quick service intervention or fault diagnosis. Thanks to the Ethernet port, it is also possible to connect the system to the customer's Industry 4.0 system.

on demand

Handling trolley for rolls (large packaging) up to 1000 kg

Trolley for transport and handling of large-roll rolls up to a diameter of 800 mm and a total weight of 1000 kg. The trolley significantly facilitates the transport and attachment of the roll to the quick-release clamps (snap-in bearings) on the machine. With integrated hydraulic lift and brake.

Tech. specification: Load capacity: up to 1000 kg |

Detail: The cart is equipped with a pair of rails to help hold the roll on the cart surface. The truck is made in yellow signal color. Large wheels with rubber coating reduce noise when transporting the roll. The height of the loading area is adjustable by means of a foot-operated hydraulic lift. Height reduction with lever. The wheels are equipped with a brake to lock the truck in place.

on demand

Automatic pre-cutting of self-adhesive felt on paper carrier ASP-1J

The ASP-1J is designed to precut the upper self-adhesive layer of material on a paper carrier. The paper carrier must remain in its entirety so that it can be rewound. Length of cut material adjustable in the range of 5 - 400 mm. The machine is fully automatic and equipped with a servomotor, frequency converters and Omron control.

Tech. specification: Max. installed machine power: 1.75 kW | Current system: 3 NPE TN-S | Control voltage: 24 V DC | Supply voltage: 400V AC, 50Hz | Max. compressed air operating pressure: 6 bar | Workplace noise: <75 dB | Max. machine dimensions (l x w x h): 4640 x 1600 x 1950 mm | Dimensions measured with material and open covers. | Gross weight: 250 kg | This machine answer all safety considerations and specification CR and EC! |

Detail: The machine consists of the following parts: | Unwinder independently controlled by a dancer and an analog sensor with a frequency converter and safety end sensors. | Own cutting part with a strong pneumatic cylinder and a precisely adjustable stop. br> Cutting part number 2 (not mounted on the photo and video) with the possibility of another shaped or straight cut. o precisely defined (system set) distance with an accuracy of 0.01mm. The feed is provided by a servomotor. | The winder, which, like the unwinder, is controlled independently by means of a dancer and an analog sensor. | options for displaying the service and diagnostic menu. The display also shows error messages, the time to complete the operation, according to the set number of pieces. |

on demand

Jigsaw of small medical drapes SK-600/HR

Fully automatic machine for folding medical material in a roll from a width of 370 mm (up to 600 mm) into final packages with dimensions of 65 x 76 mm (up to 90 x 110 mm) with a cycle of up over 1.5 pieces in 1 s. The machine is equipped with a Siemens control system.

Tech. specification: Max. machine power: 19.2 kW | Current system: 3 + N + PE TN-S | Supply voltage: AC 400V, 50Hz | Max. compressed air operating pressure: 6 bar | Workplace noise: <65 dB | Max. machine dimensions (l x w x h with material): 7600 x 1900 x 1920 mm | Gross weight: 2 300 kg | | Width of processed material: 370 mm | Blank size: 375 x 450 with tolerance ± 5 mm | Folded drape size: 65 x 76 mm with tolerance ± 5 mm, max. 90 x 110 mm ± 5 mm | Warehouses: 5x longitudinal warehouse, 3 x transverse warehouse | Minimum machine cycle: 1.5 veils / 1 second | Operation: 3 shifts / 7 days a week

Detail: The machine consists of the following parts: Material unwinder the roll is based on a lightly mounted pneumatically expanded shaft Dancer for controlling the speed of rotation of the unwinder according to the current speed of the machine Longitudinal folding mechanism accordion folds adjustable lower and upper panels Edges of top panels cooled by friction heating Set of straightening / knocking rollers for leveling any folds Assembly of draw cylinders. The material is rotated 90 degrees between them. Behind them, the material is already oriented horizontally Pair of belt conveyors 1 located behind the rolling rollers, guide the longitudinally folded material into the dividing space Rotary (anvil) knife that separates the individual drapes. The division takes place against a steel cylinder. Drive of the dividing rollers by a servomotor Belt conveyors 2 remove separate material. The circumferential speed is higher, basic than the speed before division, thus creating a gap between the separate pieces needed to create time for the transverse folds Belt conveyor system for transverse warehouses. At the warehouse location, the material is pressed into the next set of belts / belts by the edge of the folding knife, thus creating the first warehouse in 1/3 of the piece. The tynto system is placed on the machine 3 times in different orientation positions to achieve the desired result. Belt conveyor moves the folded piece to the hopper, where it is moved by an attachment, which at the same time creates space for the next piece with each step of moving the stock System for optical separation of the required number of pieces. Each piece entered (for example, every 70th) will be extended so that the operator, who manually picks the products, has easier orientation Stacking tray The operator at the machine outlet takes a suitable number of pieces by hand and places them in a box SIEMENS S-1200 control system, SIEMENS servomotors, Kyence sensors, TURCK, SICK Elimination of statics by grounding, connecting parts The safety of the device is solved by means of covers with a transparent field of view made of polycarbonate. Cover door secured with limit safety switches. There are emergency stop buttons (TOTAL STOP) in the operating positions Control terminal touch panel for setting and optimizing machine parameters and production requirements (cycle, lengths of cross stocks, piece counters, number in batch, service menu, diagnostics .......) Sections of longitudinal and transverse warehouses ready for possible replacement in the future the possibility of mechanical separation, electrical installation the sections have their own el. substation with separate connection to the control system SW preparation for OI collection of data on the use of the machine Remote access installed

on demand

NoName tape and velcro cutter overhaul - for automatic velcro cutting

The NoName machine is designed for cutting, cutting especially Velcro. this machine was brought to us as partially non-functional (accuracy + - 3 mm, low speed). An analysis was performed and then we installed the machine with a fast PLC with a touch screen. By adjusting the settings of the frequency converter together with the new control system, an accuracy of + - 0.1 mm was achieved with increasing speed (0.6 s / 1 piece 50 mm long).

on demand

Welding machine SVS/EF for filter materials

Specially mature pneumatic operated machine for sealing filter materials by fusing wire.

Detail: Machine for production untipical filter-bed. Specially identified for small-lot production. Shift material by hand. After press foot-operated control pedal happen to perfect sealing-in two strata material on.

on demand

Tie dicing machine DPR 2 - for rubber textile materials and velcro fastener portion

Special dicing machine for automatical portion with pre-set longitude and quantity portion cycles.

Detail: This machine is fit for velcro fastener or rubber textile materials.

on demand

Ultrasonic welding machine for plastic profile

Machine destined for ultrasonic welding of plastic profiles. Machine is fully automatic, works with special software and touch screen LCD.

Detail: This machine use sophistry driving system with touch screen LCD. It is usable for many types of plastic profiles (universal).

on demand

Ultrasonic NC machinery

Machine destined for cutter and welding sheeting and textile with admixture synthetist. Machine is fully automatic, works special software for 2D drawing and gruelling plans. Work with PC and 3 seed guidance ultrasonic head is secured currency HQ and accuracy cut.

Detail: It is only speciment pilot machinery working on tenet NC machine.

on demand

Cutting machine for pared plastic part KRP 1 / ABB 1

Machine for trimming plastic intake from extract part by the help of robot (automatic) troop.

Detail: Stationary machine destined for build into automatic lines. Machine clean off and slaughter intake in production plastic part.

on demand

Cutting machine for pared plastic part KRP 2 / ABB 2

Machine for trimming plastic intake from extract part by the help of robot (automatic) troop (evolution 2).

Detail: Stationary machine destined for build into automatic lines. Machine clean off and slaughter intake in production plastic part.

on demand

Cutting machine for pared plastic part KRP 3 / ABB 3

Machine for trimming plastic intake from extract part by the help of robot (automatic) troop (evolution 3).

Detail: Stationary machine destined for build into automatic lines. Machine clean off and slaughter intake in production plastic part.

on demand

Stacker of plastic part ZPD 1 - fulfilment with cutting shear

Automatic spreader, computing machine with possibility cut plastic profiled material.

Detail: Plastic profile is merging from infinitely zone, that is on-shorn on preconfigured longitude and arithmetic and found collator to the trim for withdrawal user.

on demand

Agitator for loose material (mixture machine)

Machine for mixture loose, granulated material to the mine. grit size 2 mm...

Tech. specification: Tension AC 230V | Amperage 6A | Ratio mixtures dirigible freguency changers |

Detail: Machine equipment drive motor freguency transducer and special driving system (program) for setting conditions and quantity assorted materials. Sizes chambers and quantity material/throw according to setting consumer.Frame machinery AL, covers chambers polycarbonate,spatulae arrangement AL, motor NORD, Siemens...Supplies vc. vacual arrangement (pumps) or snail. conveyer.

on de0on demand

Turntable on spray cathartical swab textile

Machine for transaction efficient spray cathartical emulsion to swab materials.

Tech. specification: Potential AC 230 V | Amperage 1.7 A | Speed: adjustable | Used first-rate seat power control spray-gun - 2 piece

Detail: Machine espressivo efective work with spray emulze to material. From attendance requires only merging new and extraction already sprayed with material. Adjustable rate cycle and veer.

on demand

Machine for package mops

Machine for efective package mop to the set bag.

Tech. specification: Potential AC 230 V | Amperage 2.5 A | Speed: adjustable |

Detail: Machine espressivo efective work with package mop to the bag. Speed of rotation single thorn in extenso adjustable. Altitude machinery conformity highs average euro-citizen.

on demand

Technological set machine for chemical, medical industry

Set five highly professional machine designate on processing medical supplies in chemical environment.

on demand

Suture, stitching roles, roll (textile material) - low

Machine type: SŠR6.20SIRUBA700E

Detail: Machine is identified on transverse suture textile material. In this fulfilment on suture unwoven light PP and PE textile. Connection more smaller role in traverse originate role about high average thereby and a great deal of (longitude) wound material. Machine be calculated for role about longitude 6200 mm, longitude needlework is however in extenso adjustable.

on demand

Suture, stitching roles, roll (textile material) - big

Machine type: SŠR6.20SIRUBA700E

on demand

Suture, stitching roles, roll (textile material) with cutting

Machine type: SSR6.20 with cutting machine KM RS 100.

Detail: Make-over fulfilment machinery for passing suture more role on. Be instrumental towards transaction big role from small role. Use special hemming machine stitch.

on demand

Cutting, separatory funnel sling, ropes - for HSG 00

This machine is identified especially to dividing synthetic ropes, rope and sling. Act about bedside table to stationary fusing heat cutter HSG 00 (to both types).

Detail: Bedside table with passing storage top range on spring, possibility and with decoiler sling. Bedside table is frame, top range with ruler and backstop, canopy against contact glowing knives attended.

Other accessories:
Unwind reel		Eur 264.2,-

Eur 893.6,- net of VAT

Automatic machine to cut ceramic cylinder

This custom machine serve for exact terms dividing ceramics cylindrical shape on in advance given to lots in longitude 5 - 10 cm.

Detail: Is consideration on minimisation rising dust at cut. Pneumatic drive element for minimisation attrition machinery. Machine is drawn to the 24 hours run.

on demand

Saw, separatory funnel to the plastic conduit BRX 1000 - 1600

This machine is identified especially to dividing plastic piping.

Detail: Install oneself assembling from guiding subframe and from two fixative wreaths. Piping are pinching in 6 and 4 fixative wreaths. Outside table about longitude 8 m be instrumental towards supporting tag cutty piping and is division into two parts. Part further from saw has couple roller sequenced to the vee, which allows transverse centring ends piping on conveyer. Saw is identified entirely to dividing PE plastic conduit with requisite look askance. Slaughter from oven-ready food longitude from 12 m to the 2,5 m about OD 315 mm when 1600 mm with high accuracy and smoothness cut.

on demand

Cutting, separatory funnel sling, ropes

This machine is identified especially to dividing hard synthetic ropes, rope and sling.

Detail: Machine was engineered with have a respect to specification and recipe valid in EC tool design barter, possibility different Angles edge, possibility using unilateral knives against stand-by cost mats.

Eur 6711.9,- net of VAT

Cutting, separatory funnel sling, ropes

This machine is identified especially to dividing hard synthetic ropes, rope and sling.

Eur 8762.7,- net of VAT

Automatic machine to cut plastic materials

This machine be instrumental towards accurate dividing intake from plastic (PP, PE) part

Tech. specification: Tension AC 230 in | Flow max. 16 A | Noisiness max. 75 DB | Toleration cut +-0.7 mm |

Detail: Machine belong untouched by human hands lines with serving robot, which ensure exact terms drift part to pared on knives and resulting sealing-in turnings arose at cut. Machine is drawn to the without end running for car industry.

from Eur 1536,- net of VAT

Automatic machine to cut plastic materials - special blades

This machine be instrumental towards accurate dividing intake from plastic (PP, PE) part by the help of guidance robot.

Tech. specification: Noisiness max. 15 dB | Toleration cut +-0.7 mm | Special blade 2x2 |

Detail: Machine belong untouched by human hands lines with serving robot, which ensure exact terms drift part to pared on blade. Machine is drawn to the without end running for car industry.

Eur 3504.9,- net of VAT

Cutting press IC KLEINEWEFERS (Germany)

An older die-cutting press for creating samples (slitting cut) of the Kleinwefers brand, intended especially for cutting and die-cutting sample materials. The press was basically refurbished and sold as a bazaar. We can provide other bazaar presses, according to your requirements!

Tech. specification: Voltage: AC 400 V, 50 Hz |

Detail: The press is equipped with a mobile table with a stepping device. This press was exhibited at this presentation as a bazaar and at the customer's request it was refurbished and repaired before its sale. We also provided accompanying documentation for the press.

on demand

Remake of fully automatic face mask production line

We repair a pair of fully automatic lines for face masks producing imported from Thaiwan / China. The line is now fully functional and meets all regulations valid in the Czech Republic.

Tech. specification: Machine producer: wanjinmachinery / healthyco | Staffing requirements: 2 operators | Support mask production type: flat non-woven mask 3/4 layer | Power: 11KW | Output: 40 - 120pcs / minute This machine answer all safety considerations and specification ČR and EC!

Detail: Production line structure： | A host (face mask making machine) plus two ear band welding machines (outer ear bands) are connected by a one-to-two transmission line. It can realize the full-automatic production process from coil feeding, folding and pressing, and slitting, ear band feeding machine welding, and unloading. |

on demand

Back to full catalog listing Print the selection Gop to back to main page

Name / Validity	Domain and processor	Saved info
Cookchecked 30 days	www.robex-dk.cz / ROBEX DK, s.r.o.	cookies preference
PHPSESSID until the end	www.robex-dk.cz / ROBEX DK, s.r.o.	about user relations
sdmenu_my_menu 30 days	www.robex-dk.cz / ROBEX DK, s.r.o.	left category menu

Name / Validity	Domain and processor	Saved info
YouTube 0 - 300 days	www.youtube.com / YouTube	about playing products videos
Google 1 - 90 days	www.robex-dk.cz / Google	about your visit