ROBEX DK, s.r.o. - cutting technique, accessories, custom made machinery

SHOPWITH NOT ONLY
PROFESSIONALLY
TECHNIQUE CUSTOM
MADE SINGLE-PURPOSE
MACHINES

CART (0)

On-line catalogue - english

Other machinery, custom made special machines

Roll Slitting Machine - tapes from roles cutting

Paspulator PKV-2000 - roll cutter (foil, foam, rubber, textile)

The roll splitter is intended for transverse cutting of hard and soft materials when the roll of material is spun using a pressed rolled disc knife. Adjustable shaft speed limitation with material, central nut with mandrels to lock sleeve on shaft, quick face lock, two-handed safety trigger. The roll is cut including the paper tube (can be limited by a screw).

Detail: Cutting takes place using a disc knife with a large diameter, which is guided by a manually guided movable arm against the material rolled on a motor-driven shaft.The frame construction of the machine is made of steel + aluminum AluTec profiles. A linear guide with an arm guide is located on this frame in a horizontal plane. A disc knife is fixed on this arm. The shaft drive is an asynchronous motor with the possibility of a continuous speed change. Thanks to the used frequency converter, operation is also economical. The knife cover is opened by a wheel that runs along the upper part of the roll, i.e. the position of the arm above the material. The arm has a handle with a two-handed trigger, a manual lock for a strong hold of the arm at the point of the cut.The safety of the machine is ensured by the position, the cover and the safety double-circuit module.

on demand

Paspulator PKV-1000 - automatic film roll cutter

The foil roll divider is intended for transverse cutting of solid materials (when roll rotate) into paspules (discs) of different widths. A large cutting disc is used for cutting, which is guided into the cut by a motor (servo actuator) with a smooth change of speed. Adjustable speed limitation of the knife and rolling rollers, locking and a lesion indicator of the cutting position, controlled by the Siemens system. The automatic extraction of the chips is a matter of course.

Detail: Cutting takes place using a large-diameter disc knife, which is guided by a motor-guided arm against a material rolled on a pair of adjustable driven rollers. | | The construction of the machine frame consists of AluTec steel + aluminum profiles. A linear guide with an arm guide is located on this frame in the horizontal plane. A disc knife is mounted on this arm. The knife drive is an asynchronous motor located on this arm with the possibility of a smooth change of speed. The knife cover is opened by repacking, ie the position of the arm above the material. The arm has a handle for manual (quick) position change, a rolling wheel for precise, precise position adjustment, pneumatic locking for strong holding of the arm at the cutting site (without locking the cutting cycle cannot be started) and a laser pointer to facilitate measuring the cutting position. The arm is pushed into the cut by means of a servo drive. Driving upwards always takes place at maximum speed. The downward (cut) out of the material also takes place in accelerated mode. thanks to the inductive sensor, the movement of the arm is slowed down only before the height of the placed diameter of the roll is reached. Bosch Rexroth units are used to drive the arm. Ideal accuracy is also achieved by rolling the roll on rubberized rolling rollers, which are adjustable (for different roll diameters). A pair of Siemens frequency converters is used to drive the cylinders. A Siemens system with remote management is used for control. The whole system is built as a semi-automatic. Measuring the position of the cut manually, own cut fully automatic. Sawdust and chips are always removed from the cutting point into the plastic bag during the cut. Thanks to the branch, this extraction can also be used for manual vacuuming.

on demand

Paper tube divider RBRD-2 (diameter up to 500mm, wall thickness up to 35mm)

Machine for cutting and dividing paper and cardboard tubes up to a diameter of 500 mm with a wall thickness of 35 mm. The cut takes place by rolling the cutting disc along a rotating tube. The cut is made manually by pressing the blade on the cut tube through the lever of the cutting arm. The sockets are threaded on the central mandrel with a clamping disk.

Detail: The design of the machine is chosen simply and efficiently to achieve easy and safe operation by the operator. The basic supporting part with the drive and the cutting arm consists of a frame of welded construction made of steel profiles, the supporting frame of the separate tube is made of aluminum anodized profiles. Both parts are connected by screwed mounting plates. The superstructures are generally also made of aluminum anodised profiles. The surface treatment of steel parts is solved with powder firing paint and galvanic galvanizing The smooth rotation of the cut tube against the cutting disc is ensured by rolling on rubberized drive rollers, which also serve as a support when the blade is pressed against the tube. The required torque is determined by an electric motor with a gearbox and an output shaft fitted with a toothed pulley, which drives the pulleys by means of a toothed belt. The optimal tube speed is set by the manufacturer on the frequency converter and we do not recommend changing it.

on demand

Paspulator PS 5PP - fast rewinder with longitudinal division of rolls (when rewinding)

The automatic device is designed for longitudinal cutting of materials during rewinding from a roll of max ø 1150 mm, width 1,600 mm and weight 300 kg into strips (discs) of various widths, intended for further processing. Industrial razor blades are used for cutting, with the possibility of their mutual distribution across the entire width. Adjustable speed limit, side straightening, controlled by PLC with touch. screen and measuring length, rewinding speed up to 2.7 m / s.

Tech. specification: Electrical supply: 3NPE 400V / 50Hz TN-S | Power input: 8.1kW | | Rewind / cutting speed: automatically variable (min. 2.0m/s, max. 2.7m/s) | Motor: 2x SM controlled as servo | Cut: razor blades on interchangeable holder | Control: PLC + HMI with touch screen | The device can be used as a viewing and rewinding machine with straightening edges Input Roles: | Material: 17-110g/m2 | Roll diameter max.: 1150mm | Roll weight max.: 300Kg | Roll width max.: 1600mm | Inner diameter of roll sleeve: 76 mm | Output Roles: | Output roll: according to the set required length (cm) | Roll weight max.: 300kg | Rewinding working speed (minimum): 120 m/min (at 100% potentiometer) | Razor safety covers for changing brackets

Detail: To achieve the required dimensional tolerance, the most suitable method of cutting during rewinding is. Cutting takes place using razor blades on a rising frame while rewinding the roll of material. | | The construction of the machine frame consists of steel + aluminum profiles AluTec. The unwinding and winding shaft is expansion, pneumatic for the inner ø of the tube 76 mm. The ends of the winding shaft are square in shape. The shaft is mounted in tilting bearing housings, driven by an electric motor with a gearbox, where servo control with a speed of 0-3000 rpm is used. Before clamping and before introducing the material, it is necessary to arrange the divided cavities on the shaft according to the required dimensions. | | The speed is controlled by connecting the roll diameter sensors / potentiometer / dancer so that it is always min. 2m / s. The PLC with a touch screen also displays the currently measured length. | | The razor holders are slidably mounted on a removable aluminum profile, mounted on a tilting arm. Removable aluminum profiles (2 pcs.) For easy and quick exchange of cut positions. Latches with a tension spring located on a fixed central frame are used to secure this arm in the rest position. | | The device aligns the edges of the laid material. Based on a pair of sensors, the system allows the transverse movement of the material so that its edge is always guided on the winding shaft in the same place. The position of the sensor in the transverse direction can be adjusted to a certain extent and thus determine the position of the edge of the material.

on demand

NC controlled full automatic machine RBP - NC for precision transverse cutting

Paspulator RBP - NC is designed for transverse paspule cutting. Cutting from rolls of woven and non-woven fabrics or coated textile and similar materials, for further processing. RBP - NC operates in full automatic mode. The actuators are designed using stepper motors with high precision positioning of settings and programs.

Detail: High precision cutting machine with PLC controller. You can save and load all set parametrs to (from) memory. |

on demand

Papulator RB PP-2 - roll cutting while rewinding

The machine is designed for cutting materials when rewinding from a roll of max. 450 mm, width 1 500 mm and weight 280 kg to belts (rolls) of different widths. Equipped with a frequency converter for continuous speed change, pneumatic brake, side straight, controlled by PLC with touch. these and length measuring.

Detail: To achieve the required dimensional tolerance, the best way to cut is during rewinding. Cutting is carried out using razor blades on a rising frame while rewinding the roll of material. | | The frame of the machine is made of steel + aluminum profiles AluTec. The unwinding and winding shaft is expandable, pneumatic for the inner diameter of the tube 76 mm. The ends of the winding shaft are square-shaped. The shaft is placed in hinged bearing houses, driven by an electric motor with gearbox. Prior to clamping and material insertion, it is necessary to arrange the split tubes according to the required dimensions on the shaft. | | The touch screen PLC also displays the currently measured length. | | The tension of the material required during rewinding and cutting is ensured by wrapping it through the braked cylinder. It is braked by a pneumatic friction brake, the effect of which is regulated by a pneumatic pressure reducer. The blade holders are slidingly mounted on a removable aluminum profile attached to the swing arm. Removable aluminum profiles (2pcs) for easy and quick change of cut positions. To secure this arm in the rest position, use the tension spring latches located on the fixed central frame. To prevent unwinding of the roll of material in the unwinding part, the machine will be equipped with a belt friction brake with a weight. A friction disc is mounted on the shaft at the friction brake strap. | | The machine aligns the edges of the material to be laid. The system allows the transverse movement of the material, based on the sensor, so that its edge is always guided to the winding shaft at the same location. The transverse sensor position can be adjusted to a certain extent to determine the position of the material edge. The range of movement for holding the edge is + 70 mm.

on demand

Paspulator - machine for roles cutting RBP 1500

Special machine for cutting material in roles. Cutting mechanism for perfect accuracy. It is good for cut tape or pile sides of role. Paspulator has statical special knife, pneumatical shaft for fast change of role, frequency modulation for speed change, double-hand starting of machine and other funnctons.

Detail: Can you cut tape from role? Can you pile sides of role?Paspulator is machine fit for cutting from role without rewinding material. It is our machine with genial use. You insert your role to pneumatical shaft, measure position of cut and start machine. Special knife is good for material cutting with paper cup or without paper cut. General summary: | gripping of the role with material on stretching pneumatic shaft (length to 6.2m) | support rollers for inhibits shaft deflection | gripping of the shaft into the special fastener bearings | automatic variation in revolutions dependent on process of cut (possibility) | cutting mechanism special wrought knife, bayonet gripping of the knife for angular setting | (according to different materials various types of the knives) | axially linear shift of the cutting mechanism with pneumatic brake in linear Alu lead | machine suits to all norms of Czech republic and EU |

on demand

Paspulator - cutting role, chaff - self-generating method PRR-O/MIL

Machine on dividing material in role inclusive possibilities kerf margin role. Cheapen variant machinery on dividing textile material self-generating method!

Detail: instrumental towards coarse, but very nice trim role, cut material. Quality cut directly unwind from qualities winding-up input material.

on demand

Paspulator - machine for cutting role with rewind PP–1/HR

Machine for cutting role with rewind. Super quality cutting.

Detail: Lengthwise cutting unwoven textile wound at role. Cutting proceed by the help of special industrial blade placed on rampant frame, at contemporary rewinding role material.

on demand

Paspulator - machine for cutting role with rewind PP–2

Machine for cutting role with rewind. Super quality cutting.

Detail: Lengthwise cutting unwoven textile wound at role. Cutting proceed by the help of circural blades placed on rampant frame, at contemporary rewinding role material.

on demand

Back to full catalog listing Print the selection Gop to back to main page

Name / Validity	Domain and processor	Saved info
Cookchecked 30 days	www.robex-dk.cz / ROBEX DK, s.r.o.	cookies preference
PHPSESSID until the end	www.robex-dk.cz / ROBEX DK, s.r.o.	about user relations
sdmenu_my_menu 30 days	www.robex-dk.cz / ROBEX DK, s.r.o.	left category menu

Name / Validity	Domain and processor	Saved info
YouTube 0 - 300 days	www.youtube.com / YouTube	about playing products videos
Google 1 - 90 days	www.robex-dk.cz / Google	about your visit